In recent years the Wire electrical discharge machining process plays a vital role in machining Hardened alloy. In this study Monel 400 alloy was chosen as a workpiece, while machining this hardened alloy it commonly shows poor surface finish and corner inaccuracy. In order to improve the machining performance the Multi pass cutting was introduced. Here multi- pass cutting is performed by rough cut followed by two trim cuts. The control factors such as offset distance, corner angle, flushing nozzle height, pulse on time, pulse off time, open circuit volts and wire tension are selected as process parameters for the responses such as cutting speed, surface roughness and corner error. By using Taguchi design the experimentation were carried out and the results were analyzed. The result shows that the surface finish and corner accuracy were improved if the machining had done with single trim cut. And also result reveals that if the number cut increases beyond the single trim cut it affects the productivity and accuracy. Hence this study proves that the single trim cut is enough for achieve a better results. On the other hand the effects of process parameters during Single trim cut and multiple cuts are compared and reported.
Nowadays, the recent strategy of covariance matrix adaptation evolution strategy (CMA-ES) is become a standard evolutionary technique for multi-objective optimization (MOO). In order to attain the linearized process of constant temperature anemometer (CTA) the unsophisticated procedure is offered. In this paper, to have linearized process of CTA the function are optimized with the optimal values of mean square error which is determine by the nonlinear ratio metric logarithmic objective strategy to develop the signal linearity of CTA. Here, the modified multi objective covariance matrix adapted evolution strategy (MMO-CMAES) is modified with the matrix function and generate the process for convergence is reduced to optimum the system with a reliable access. The proposed system is processed with the reduction of generation process which is used to adapt the matrix requirement and the efficient process of parallel enactment is done for temperature linearization. The proposed system is simulated and attained the results analysis by using Lab VIEW 7.1. The study purpose is to have an efficient optimal resistor value, time complexity, reduction of noise and generations and reliable process.
Wireless sensor nodes are deployed, it focus mainly the coverage and connectivity between nodes. Generallly nodes coverage range is fixed, sometimes which are placed in more distance cause out of coverage range from sender node to desination node. The network does not have any path analyzer node. After packet drop to identify the out of coverage among sensor node. it reduce packet delivery ratio, and network connectivity ratio. So, proposed Enhanced connectivity for nodes to measure coverage range (ECCR) is used to provide better coverage based communication among sensor nodes. Affected routing path is detected at initially, since alert message packet is forwarded from source node to destination node. Anchor node based path monitoring algorithm is constructed to monitor abnormal activities of each sensor nodes which are placed in network environment. The abnormal activities indicates the more packet drop during communication since its coverage range goes to out of limit. It increase connectivity ratio, and packet delivery ratio.
Buck boosta convertir Is a électronique convertir That convert DC voltage at. a certain level input to DC voltage at certain level output. Control system is needed to keep the output voltage according to the set point. Buck boost converter system is implemented control mode PI and PI-Fuzzy.Performance of PI-fuzzy controller for buck boost converter is conforma than convetional PI controller when both controller are subjectif to the same operation. The optimization the performance contrrol system (. PI-FLC control system performance with 40 V set 10 V input has the best stability performance with maximum overshoot (Mp) = 0 V, settling time (Ts) = 0.09 seconds, peak time (Tp) = 0.017 seconds, rise time (Tr) = 0.01 sec and steady state error (Ess) = 0.1 V) , the wind enegy capture to enelctricity conversion are optimization.
Protection system is a system to keep the process in order to remain safe in the event of an undesirable state. Analysis of the Safety Integrity Level (SIL) was conducted by doing Fault Tree Analysis (FTA) and Risk Graph in a case study on Carbon Dioxide (CO2) Absorber 101-E Unitin the Ammonia (NH3)) plant of fertilizer industry. Fault Tree Analysis is used to determine the SIL based on the potential rate of failure of components in Carbon Dioxide (CO2) Absorber 101-E Unit. Here it is found that the SIL value of Benfield Solution Lean pump P-108J and P-108JA are in SIL 1 with the Probability Failure on Demand (PFD) 0.4121. While the Risk Graph is used to determine the value of SIL in each scenario of HAZOP Carbon Dioxide Absorber101-E Unit with some parameters such as consequences (C), the frequency of the field visit (O), the chances of avoiding danger (F) and the possibility of damage to the components (W). Here it is found that low level scenario is at a value of SIL 2.